Select Vehicle

Priced from:

$139.48 - $491.85
Product #: 27687G Brand: Bestop
Customer Rating: 3.5 of 5 stars
  • Bolts directly to frame (97-10 Wranglers)...retracts for off-roading
  • It's a nerf bar when retracted, a convenient step up when pulled out!
  • Spring loaded mechanism allows for smooth step retraction/operation
  • Mounts directly to frame using factory mounting points
  • Flat stepping surface remains flat even when stowed
  • Heavy-duty rocker guard piece helps protect against dents and dings
In three easy steps you can get a helping hand into your JK! Simply slide the step forward, pull out and then down. Step also retracts out of the way so rocks and rugged terrain are of no concern when you go off-roading. Made of 2-1/2" diameter steel tubing with 1/8" wall thickness and a special layer of E coat for superior resistance to rust and corrosion.

NOTE: Wrangler Rubicon models require factory rocker panel guards be removed to install Slider Step.

Overall Rating
3.5 out of 5
3.5 out of 5
Open Ratings Snapshot
Rating breakdown 2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2 of 2(100%)reviewers would recommend this product to a friend.
Product ReviewsWrite a review
Overall Rating
3 out of 5
3 out of 5
quality parts, lousy mounting
March 3, 2012
Location: Mineral, Va
How often do you shop at JC Multiple Times a Year
" The installer nut for the frame rivets COULD (suggestion) have a knurl or other device to keep the rivets from spinning in the frame while installing and then destroying the knurls that are on the exterior of the rivets. Be VERY CAREFUL that the rivet does NOT TURN when tightening the installer bolt to 30 ft lbs of torque. The rivets are too soft and distort and abrade way too easily. some method should be incorporated into the installer tool assembly to keep the rivet from turning in the frame while installing. The steps themselves get a five star rating from me, but the very questionable installation instructions and method get a one star, so overall a 3 is given. "
Pros: heavy duty parts, well powder coated, easy install except for frame rivets
Cons: frame rivet installation is not well covered in instruction sheet, difficult at best to install
0out of 0found this review helpful.
Was this helpful?helpful0unhelpful0
Overall Rating
4 out of 5
4 out of 5
installing step not so easy
January 31, 2010
Location: Chester, Ca
How often do you shop at JC Multiple Times a Year
" Installation was difficult. Step front bottom bracket did not allow enough room to bolt side plate front hole to body without hitting floor pan. Bracket was pushed against frame to body mounting post tight. MFR should have slotted bracket one more inch and it would have worked fine on my 1992 jeep wangler. The 8mm washers furnished were not larger enough and I had to get the next size larger, so they would not slip through the slotted holes in the bracket. The only other thing is it would been nice if they had furnished an extra threaded insert with the package in case you screw one up. Which I did. After it was installed I was very happy with the appearance and it functions perfectly. "
Pros: strong and just the right step hight for my 1992 jeep
Cons: did not fit as well as expected
9out of 9found this review helpful.
Was this helpful?helpful9unhelpful0
CARR HOOP STEPS Priced from: $57.55 SET
BESTOP TREKSTEP FOR PICKUPS Priced from: $169.99 Sold Individually
GO RHINO UNIVERSAL SIDE STEPS Priced from: $63.09 Sold Individually
BULLY ADJUSTABLE SIDE STEPS Priced from: $101.27 Set of 2
DEE ZEE SIDE STEPS Priced from: $166.15 Set of 2
BESTOP TREKSTEP SIDE STEPS Priced from: $199.99 Sold Individually
CARR SUPER HOOP STEP Priced from: $140.20 Set of 2
CARR SIDE STEPS Priced from: $36.39 SET